• Gardner Bender Get 1200
• Gb Instruments Get 1200 User Manual Free
• Gb Instruments Get-1200 User Manual
• Gb Instruments

Gb gdt 200a manual booklad.org Download links for Gdt 205 Multimeter.doc MSWord Document. Save on Gb Instruments Gdt 200a Manual deals from a selection of popular stores at DealTime. Test Instruments. Testing equipment can be put to good use ensuring that electrical equipment is properly installed and safe to operate. Faulty installations can be lethal; the condition of electrical installations can be established when contractors use test equipment.

or current than the set range of the
multimeter will allow.

4)

Do not touch the metal

probes of the test leads when making a
measurement.

5) Replace worn test leads. Do not use test

leads with broken or tattered insulation. Only
test leads meeting ETL, cETL, CAT II
300V IA can be used in this multimeter.

6) Discharge a capacitor before measuring it.

7) Remove the test leads from the circuit being

measured as soon as the test is completed.

8)

Do not measure voltage

when the function/range switch is set on
the resistance (ohms) or the current (mA)
settings. Never measure current when the
meter is set on the resistance range.
Never measure AC voltage when the
meter is set on DC voltage or DCmA.
Setting the meter on the incorrect function
may burn out some of the internal circuitry
and may pose a safety hazard.

3. Operating Suggestions

1) Set the function/range switch to the proper

position before making a measurement.
When the voltage or current is not known, it
MUST be determined that the capacity of
the selected range will handle the amount of
voltage or current in the circuit (see #3
under

For Your Safety). Always start with the

highest range in the function. If the
reading falls within the range of a lower
setting, reset the function/range switch to

!

WARNING

!

WARNING

6

5

the appropriate setting for greater accuracy.

2) Avoid placing the meter in areas where

vibration, dust or dirt are present. Do not
store the meter in excessively hot, humid
or damp places. This meter is a sensitive
measuring device and should be treated
with the same regard as other electrical
and electronic devices.

3) Using the meter in areas with high magnetic

fields can result in inaccurate readings. For
greatest accuracy, lay the meter flat on a
non-metallic surface.

4) When the meter is not in use, keep the

function/range switch in the OFF position.
This keeps the needle indicator from
deflecting or ”bouncing” excessively.

5) When disconnecting the test leads from

the unit, always grasp the leads where the
input jacks meet the meter housing. Never
pull the leads out of the jacks by the
insulated wire or transport the meter using
the test leads as a carrying strap.

6) Never immerse the meter in water or

solvents. To clean the housing use a damp
cloth with a minimal amount of mild soap.

Gardner Bender Get 1200

7) If the resistance (ohms) function of the

meter is not going to be used for a week or
more, remove the internal battery to avoid
potential leaks that may damage the unit.

3.1 Preliminary Adjustments

Fully seat the test leads in the correct input
jacks. If necessary, using a small flat tip
screwdriver, slowly turn the mechanical zero

GMT-312 5-09 manual.qxp 5/21/09 3:04 PM Page 6

Madison, Wisconsin, United States

GB Instruments Circuit Tracker (Circuit Breaker Locator) is missing the transmitter. This piece, the receiver, seems to be functional in that it turns on and the lights turn on. It takes a 9 volt battery which is included but age of battery is unknown. Item is in good condition; you'll need a transmitter to match up with this unit.

Condition:	For parts or not working: An item that does not function as intended and is not fully operational. This includes items that are defective in ways that render them difficult to use, items that require service or repair, or items missing essential components. See the sellerТs listing for full details. ...	Brand	GB
Country/Region of Manufacture	China
Model	GET-1200

Simpson rolltop 260 multimeter mint shape works excellentFluke 8502a options-02/05/08a memory programming 6 1/2-digit digital multimeterNew exfo ppm-350c fiber pon meter (brand new)Gw multimeter model: gdm-8135Fluke 27fm, nsn no 6625-01-265-6000, multimeter/ probe/ test leads/ case

Gb Instruments Get 1200 User Manual Free

Gb Instruments Get-1200 User Manual

Uni-t ut804 true rms multimeter digital

Gb Instruments